How to Factory Reset a MAG 324 Set Top Box

In this article, we take you through the step-by-step process of restoring a MAG 324 set-top box back to it’s factory default settings.

Before proceeding, it highly recommended that your box is easily accessible as the main reset hole is located on the left hand side of the box.

The reset hole is small, so will require the use of a paper clip (or similar) with one of the ends bent outwards to aid pressing and holding the button. Do not use any sharp objects such as pins or needles, as this could damage the reset button.

You will also need to have the box plugged in, powered up and connected to your TV whilst switched on.

Lastly, make sure you have your remote to hand as this is required to configure the box after the reset has completed.

MAG 324 Factory Reset

MAG 324 Rear Panel

1. Firstly, ensure your MAG box is powered up and fully booted.

2. Now, if your MAG box has an ethernet cable connected, remove from the back.

3. Then, remove the power cable from the back of the box and then after 2-3 seconds reinsert the power.

Bent Paperclip

4. Now, immediately place your paperclip end into the reset hole, then press and hold the reset button continuously. DO NOT let go of the reset button.

5. Keep the reset button pressed in even whilst you see the Infomir logo on your TV screen, and observe the white light on the front right edge of the box.

6. The white light should initially start to blink. When this occurs, keep the reset button pressed. Don’t let go.

7. When the light starts flashing faster, let go of the reset button and then immediately press and hold it again.

Mounting RootFS

8. Keep pressing until the screen goes blue. Then you can let go.

Starting User Services

9. Now wait for the MAG box to start the factory reset process. This will involve seeing a blue screen followed by a blank black screen. This may take a couple of minutes, so please be patient…

Settings Screen

10. Once the factory reset has completed, you should enter the inner portal screen showing several icons on a dark background.

You have now factory reset your box. Next, you need to configure your box to receive your desired IPTV service.

Configure Time Server

Settings Screen

11. From the home screen, use your remote to highlight “Settings” and then press OK.

System Settings

12. On the next screen, highlight “System Settings” and press OK.


13. Next, go to “Servers” and then press OK.


14. Then highlight “General” and press the OK button on your remote.

NTP Server

15. On this screen, enter the following into the NTP server text field:

Press on KB (Keyboard) button on your remote to activate the on-screen keyboard and type this in.

Use the arrow keys on your remote to locate the correct keys and then press the OK button to select each letter or character one-by-one.

When completed, press the KB (Keyboard) button again to close the on-screen keyboard.

Then finally, press the OK button on your remote to save the time server setting.

16. Now, press the EXIT button twice on your remote to go back to the “System Settings” screen.

Add Your IPTV Service


17. From the System Settings screen, highlight “Servers” and press OK using your remote.


18. Now highlight “Portals” and press OK

Portal 1 URL

19. On the next screen, highlight the “Portal 1 URL” text field and then press the KB (Keyboard) button on your remote to activate the on-screen keyboard.

Then use your remote to enter the URL supplied by your IPTV provider

Note: The URL will be something like for example

Once entered, press the KB (Keyboard) button once again to close the on-screen keyboard. Then press OK on your remote to save changes.

20. Now press the EXIT button on your remote to return to the System Settings screen.

Configure Wi-Fi Network

21. If your MAG box uses a WiFi connection to log onto your home network, you need to set this up next. If your MAG box uses an ethernet connection, reinsert the ethernet cable at the back of the box and skip to Step 27.


22. From the “System Settings” screen, highlight “Network” using your remote and press OK.

Wireless Wi-Fi

23. Next, highlight Wireless (Wi-Fi) and press OK using your remote.


24. Now highlight “Auto (DHCP)” and press OK on your remote.

25. On the next screen, you will see available WiFi networks. Highlight the correct network you wish to use and press OK.

Wi-Fi Password

26. Now using your remote, highlight the “Key or passphrase” text field, then press the KB (Keyboard) button to activate the on-screen keyboard. Then use your remote to enter your WiFi network password, paying close attention to correct cases and special characters.

Once entered, press the KB (Keyboard) button once again to close the on-screen keyboard. Then press OK on your remote to save your password settings.

You should see an on-screen confirmation message saying your settings were “Successfully saved”.

Reload Portal

Reboot Device

27. Your box is now fully configured. So finally, highlight “Reboot device” and press OK using your remote. Press OK once again to confirm. The box will now restart.

28. If configured correctly, your MAG box should fully boot and load your IPTV service.


In some instances, some MAG boxes will not fully factory reset due to custom firmware having been loaded onto the box by the previous owner.

This occurs because the software loaded was unofficial firmware and has been designed to prevent factory resets.

If this is the case, you will instead need to reload a completely fresh copy of the official Infomir firmware for your model of MAG set top box or replace your box.

Watch the Video Tutorial

Want to see a step-by-step walk-through video? Then sit back and watch how to factory reset your MAG box from our YouTube channel.

Download Helpsheet

You can also download our PDF Help Sheet for step-by-step instructions you can save and print.